Wet & Dry Waste Smart Dustbin for House | Best science Project | Harish Projects

-
Image
 Watch Full Detailed video 👇🏻 Diagram in Video👆 //Arduino Code// //YouTube: Harish Projects //Order Electronic Parts & Project kit:  HarishProjects.com // #include <Servo.h> Servo servo1; const int trigPin = 12; const int echoPin = 11; long duration; int distance=0; int potPin = A0; //input pin int soil=0; int fsoil; void setup()  {   Serial.begin(9600); //Serial.print("Humidity"); pinMode(trigPin, OUTPUT);  pinMode(echoPin, INPUT);  servo1.attach(8); } void loop()  { //YouTube: Harish Projects //Order Electronic Parts & Project kit:  HarishProjects.com //      int soil=0;   for(int i=0;i<2;i++)   { digitalWrite(trigPin, LOW); delayMicroseconds(7); digitalWrite(trigPin, HIGH); delayMicroseconds(10); digitalWrite(trigPin, LOW); delayMicroseconds(10); duration = pulseIn(echoPin, HIGH); distance= duration*0.034/2+distance; delay(10);   }   distance=distance/2;   Serial.println(distance); if (distance <20 && distance>1) {   delay(1000); for(int i
4 comments

Build a Social Distancing science Project. Arduino code & Diagram.

-

https://www.youtube.com/watch?v=pmRF4nCdaPs




...............ARDUINO CODE.....................

 #define buzzer 6


void setup()

{

pinMode(12,OUTPUT);//Trigger

pinMode(13,INPUT);//EchoA

pinMode(6,OUTPUT);//Buzzer


}


void loop()


{


long duration, distance;


digitalWrite(12,LOW);

delayMicroseconds(2);

digitalWrite(12,HIGH);

delayMicroseconds(10);

digitalWrite(12,LOW);

duration=pulseIn(13,HIGH);

distance=(duration/2)/29.1;

if (distance < 70)     // This is where checking the distance you can change the value


{

 // When the the distance below 100cm

digitalWrite(6,HIGH);


} else


{


// when greater than 100cm

digitalWrite(6,LOW);


} delay(500);


}

Comments

Snehal Gunte said…
Thank you ��Andrew for your mother and your mother for
I have one brother who
September 15, 2021 at 2:32 AM
Post a Comment

Popular posts from this blog

Smart Bridge - Automatic Hight increase when flooding | Best science Project

-
Image
  Watch video on YouTube. //Arduino Code// //Code by Harish Projects //Orde science projects kit & electronics parts from "HarishProjects.com" #include <Servo.h> //Install this library Servo tap_servo; int sensor_pin = 5 ;   //Connect D5 of Arduino int tap_servo_pin = 4 ; //Connect D4 of Arduino int val; void setup (){   pinMode (sensor_pin,INPUT);   tap_servo . attach (tap_servo_pin);   } void loop (){   val = digitalRead (sensor_pin);   if (val== 0 )   { tap_servo . write ( 0 );   }   if (val== 1 )   { tap_servo . write ( 90 ); //If you want you can increase & Decrease servo rotation     } } //Project Diagram 1 // //Project Diagram 2// Contact us for support -  https://www.instagram.com/harishchoudhary70/
Read more

How to make Phone control RC car using Arduino #phoneControlCar

-
Image
                                     https://www.youtube.com/watch?v=EYlIB1PQ8R0&t=131s                                                    ......................ARDUINO CODE................. char t ; void setup () { pinMode ( 13 , OUTPUT ); //left motors forward pinMode ( 12 , OUTPUT ); //left motors reverse pinMode ( 11 , OUTPUT ); //right motors forward pinMode ( 10 , OUTPUT ); //right motors reverse pinMode ( 9 , OUTPUT ); //Led Serial . begin ( 9600 ); } void loop () { if ( Serial . available ()){ t = Serial . read (); Serial . println ( t ); } if ( t == 'F' ){ //move forward(all motors rotate in forward direction) digitalWrite ( 13 , HIGH ); digitalWrite ( 11 , HIGH ); } else if ( t == 'B' ){ //move reverse (all motors rotate in reverse direction) digitalWrite ( 12 , HIGH ); digitalWrite ( 10 , HIGH ); } else if ( t == 'L' ){ //turn right (left side motor
Read more

Inspire Award Project | Train accident Prevention project | Best science Project / Harish Projects

-
Image
 Full Making video Link -  https://youtu.be/nz6UnFjr__g //Arduino Code// const int trigPin = 12 ; const int echoPin = 13 ; const int LED1 = A0 ; const int LED2 = A1 ; const int LED3 = A2 ; const int LED4 = A3 ; const int LED5 = A4 ; const int LED6 = A5 ; const int LED7 = 2 ; int duration = 0 ; int distance = 0 ; void setup () { pinMode ( trigPin , OUTPUT ); pinMode ( echoPin , INPUT ); pinMode ( LED1 , OUTPUT ); pinMode ( LED2 , OUTPUT ); pinMode ( LED3 , OUTPUT ); pinMode ( LED4 , OUTPUT ); pinMode ( LED5 , OUTPUT ); pinMode ( LED6 , OUTPUT ); pinMode ( LED7 , OUTPUT ); Serial . begin ( 9600 ); } void loop () { digitalWrite ( trigPin , LOW ); delayMicroseconds ( 2 ); digitalWrite ( trigPin , HIGH ); delayMicroseconds ( 10 ); digitalWrite ( trigPin , LOW ); duration = pulseIn ( echoPin , HIGH ); distance = duration / 58.2 ; if ( dist
Read more